| Contact： Mr.Liang 13823152208 Miss.Liu 13066812208 Address：Floor 4 &6 ,Building 113, JinDi industry park FuTian District.Shenzhen,518048,P.R. CHINA Tel：0755-83895223 Fax：0755-83895233 E -mail：lqs20031118@163.com Zipcode：518048 |
PVC card production methods
Addtime：2013/11/6 16:06:17 |
Hits：
4635 | Source：Shenzhen Hengsheng smart card Co., Ltd.
Here is Shenzhen card manufacturers of PVC card making method of introduction
1.Material: white , gold, silver card printing material - transparent PVC card printing material two , thickness 0.25mm ( single-sided only one printable ) ; Inlay white or gold , silver PVC card, thickness 0.3 mm. Small A4 format , it can be done 10 standard cards .
(2) Production Method:
① Print Photo: use the appropriate resolution inkjet printer will have produced a good graphics, image printed on transparent PVC printing materials printing surface ( coated , not shiny side ) . Print resolution should not be lower than 720dpi.
② Plastic : Transparent PVC placed on the printed upper and lower surfaces ( including the graphic side ) , white or gold card , silver card placed in the middle ( the material to tear off the protective film on both sides ) . Then the laminator to a temperature of about 120-160 degrees plastic ( plastic molding temperature effect can be adjusted laminator ; 100-120 temperature can also be continuously 3-4 times a plastic , transparent PVC surface protective film so easy removal , synthetic better.
③ cut into card: good full- PVC plastic cut into small card , a small card and then tear off the surface of the protective film can ( printed material of the protective film is also available in plastic before the tear , but may affect a card surface brightness .
3 Print Application: various models of printers available with ordinary ink ( dye ink , pigment ink ) printing. In PHOTO ( Photo ) series printer image effects as well.
4 Features: Create simple, fast ; graphic clear mission, wearable.
5 Note:
① good graphic print , it should be expected to be printed ink dries ( about ten minutes ) and then plastic .
② According to adjust the best plastic laminator different temperatures. High temperature PVC will be deformed , the temperature is too low and easy layering . The temperature can also be 100-120 , a plastic consecutive times , so transparent PVC surface protection film is easier to remove , synthetic better.
③ PVC card material preservation should pay attention to moisture .
④ Please choose quality ink to enhance the image of light fastness.
1.Material: white , gold, silver card printing material - transparent PVC card printing material two , thickness 0.25mm ( single-sided only one printable ) ; Inlay white or gold , silver PVC card, thickness 0.3 mm. Small A4 format , it can be done 10 standard cards .
(2) Production Method:
① Print Photo: use the appropriate resolution inkjet printer will have produced a good graphics, image printed on transparent PVC printing materials printing surface ( coated , not shiny side ) . Print resolution should not be lower than 720dpi.
② Plastic : Transparent PVC placed on the printed upper and lower surfaces ( including the graphic side ) , white or gold card , silver card placed in the middle ( the material to tear off the protective film on both sides ) . Then the laminator to a temperature of about 120-160 degrees plastic ( plastic molding temperature effect can be adjusted laminator ; 100-120 temperature can also be continuously 3-4 times a plastic , transparent PVC surface protective film so easy removal , synthetic better.
③ cut into card: good full- PVC plastic cut into small card , a small card and then tear off the surface of the protective film can ( printed material of the protective film is also available in plastic before the tear , but may affect a card surface brightness .
3 Print Application: various models of printers available with ordinary ink ( dye ink , pigment ink ) printing. In PHOTO ( Photo ) series printer image effects as well.
4 Features: Create simple, fast ; graphic clear mission, wearable.
5 Note:
① good graphic print , it should be expected to be printed ink dries ( about ten minutes ) and then plastic .
② According to adjust the best plastic laminator different temperatures. High temperature PVC will be deformed , the temperature is too low and easy layering . The temperature can also be 100-120 , a plastic consecutive times , so transparent PVC surface protection film is easier to remove , synthetic better.
③ PVC card material preservation should pay attention to moisture .
④ Please choose quality ink to enhance the image of light fastness.
